How to Prepare Your Home for a Home Inspection (Seller's Guide)
ASADS Team · 2026-04-13
Why Seller Preparation Matters
A buyer's home inspection can make or break a deal — even on a healthy home. Inspectors evaluate every accessible area, and common oversights by sellers (cluttered utility rooms, locked electrical panels, burned-out light bulbs) can create inspection report items that look worse than they are, triggering unnecessary buyer concerns or negotiating demands.
This guide covers what Ontario sellers should do in the days before a buyer's inspection to protect the deal and avoid avoidable findings.
Access: Give the Inspector Full Access to Everything
The single biggest mistake sellers make is restricting access — intentionally or not. Anything an inspector cannot access gets flagged in the report with language like "inaccessible — recommend further evaluation." In a buyer's mind, that means hidden problems.
- Electrical panel: Must be unlocked and accessible. Clear storage from in front of it.
- Furnace and water heater: Clear at least 3 feet of clearance around all HVAC equipment.
- Attic hatch: Make sure it opens and isn't painted shut. Clear closets below attic hatches.
- Crawlspace: Clear the access hatch and provide a flashlight if the space is unlit.
- Sub-panel and disconnect switches: Leave all electrical panels, sub-panels, and disconnects accessible.
- All rooms: Unlock interior doors, including storage rooms, utility rooms, and garage access doors.
- Basement: Clear boxes and stored items from perimeter walls so the inspector can see the foundation.
Utilities: Leave All Services On
All utilities — gas, electricity, and water — must be active and operational on the day of inspection. If the home is vacant and utilities have been disconnected, the inspector cannot test the heating system, check for gas leaks at appliances, run water for plumbing testing, or verify electrical circuit operation. This triggers a follow-up inspection requirement that delays closing.
- Turn the gas back on (requires a Enbridge/Utilities Kingston tech visit) at least 48 hours before inspection
- Pilot lights on furnace, water heater, and fireplace should be lit
- Water at the main shutoff should be on
- All circuit breakers should be in the "on" position
Quick Fixes That Make a Significant Difference
These low-cost items appear in inspection reports and create buyer concern disproportionate to their actual significance:
Electrical
- Replace all burned-out light bulbs — a non-working light may be reported as a possible wiring issue
- Install cover plates on any open junction boxes or missing outlet/switch covers
- Make sure GFCI outlets in the kitchen, bathrooms, and garage are tested and functioning (press the test/reset buttons)
- If you have a generator transfer switch, leave documentation accessible
Plumbing
- Fix slow or clogged drains before the inspection
- Check under all sinks for evidence of active leaks or water staining, and repair any dripping supply lines
- Ensure the water heater's pressure relief valve is accessible
- Check that all toilet tanks fill and stop properly
Exterior
- Clean gutters and downspouts — clogged gutters are a common inspection finding
- Ensure downspouts extend at least 1.8m (6 feet) from the foundation
- Check that grading slopes away from the foundation — fill any low spots with soil
- Trim back any tree branches or shrubs touching the roof or siding
- Check caulking around windows and doors — replace cracked or missing caulk
Roof and Attic
- If you know of missing shingles, address them before the inspection if possible
- Ensure attic hatch has weatherstripping and can be opened
- If your attic has bathroom exhaust fans venting into the attic space rather than outside, address this — it's a consistent finding
Basement and Interior
- Test and replace smoke detector and CO detector batteries — inspectors test these
- Make sure the carbon monoxide detector is within 5 metres of every sleeping area (Ontario law)
- Test the sump pump if you have one — fill the pit with water to verify operation
- Replace or service the furnace filter if overdue
- Check window operation — windows in bedrooms must open for egress per Ontario Building Code
What NOT to Do Before an Inspection
- Don't hide deficiencies. If you paint over water stains without fixing the moisture source, or place rugs over damaged flooring, inspectors will often detect this anyway — and concealment of known defects is actionable in Ontario.
- Don't over-fix. You're not required to bring the home to new-build condition. Address safety issues and cosmetic items, but don't spend $20,000 renovating for a $5,000 return before selling.
- Don't be present during the inspection. Most real estate agents and inspectors prefer that sellers leave during the buyer's inspection — it allows buyers and their inspector to speak candidly.
Consider a Pre-Listing Inspection
The most effective way to avoid inspection surprises is to get your own inspection before listing. A pre-listing home inspection from ASADS gives you:
- Full knowledge of your home's condition before buyers see it
- The ability to make repairs on your schedule and budget
- A credible, third-party document to share with potential buyers
- Fewer surprises during negotiations — and faster, more confident offers
Call ASADS at (647) 801-9311 or book a pre-listing inspection online. We serve all of Ontario.