Knob and Tube Wiring in GTA Homes: Risks, Insurance & Your Options
ASADS Team · 2025-01-08
What Is Knob and Tube Wiring?
Knob and tube (K&T) wiring is an early electrical system used in North American homes from approximately the 1880s to the 1950s. It consists of single-conductor copper wires run through ceramic tube insulators where they pass through framing and supported by ceramic knobs where they run along framing. Unlike modern wiring, knob and tube has no ground wire and uses rubber insulation that degrades significantly over time.
In Toronto's oldest neighbourhoods — Roncesvalles, The Annex, Cabbagetown, East York, and parts of Etobicoke — knob and tube wiring is still present in a significant percentage of homes that have not been fully rewired. It is consistently among the most common major deficiencies identified in pre-purchase home inspections of pre-1950 housing stock.
The Core Problems with Knob and Tube
1. Degraded Insulation
The rubber and cloth insulation used on K&T wiring becomes brittle and cracks over time — particularly when exposed to heat, vibration, or physical contact. Exposed conductors are a shock and fire hazard. Insulation condition is evaluated visually in accessible areas (attic, basement, crawlspace) during inspection.
2. No Ground Wire
Knob and tube is a two-wire system — hot and neutral only, no equipment grounding conductor. This means three-prong outlets in a K&T home are not actually grounded (a common and dangerous DIY "upgrade"). Ungrounded circuits cannot protect modern electronics and create shock risks with appliances that rely on grounding for safe operation.
3. Insufficient Capacity
K&T circuits were designed for the electrical loads of the early 20th century — a few lights, an iron. Modern homes draw vastly more power. Overloaded circuits cause wire insulation to overheat, which is why many K&T fires occur inside walls and ceiling cavities where the deteriorated wiring is buried and invisible.
4. Inappropriate Modifications
Decades of amateur modifications — splices in wall cavities, improper connections to modern Romex wiring, circuits overloaded with additional outlets — compound the original system's risks. Our inspectors evaluate the overall state of the electrical system including the panel, service size, and visible wiring condition.
The Insurance Challenge
The insurance situation with K&T wiring is stark: most Ontario home insurance providers will not bind a new homeowner policy on a home with active knob and tube wiring. Some will provide coverage with a surcharge and conditions; some will issue a policy and then discover K&T during a home inspection they conduct — and cancel coverage.
Before waiving conditions on a home with K&T, confirm your broker can bind full coverage. Get this confirmation in writing. Do not assume coverage exists because a quote was provided.
Remediation Options and Costs
Full Electrical Re-wire
The permanent solution: all K&T wiring is replaced with modern ESA-approved copper Romex wiring. A new panel (typically 200-amp) is usually installed simultaneously. Cost in the GTA: $12,000–$25,000+ for a typical detached home, depending on size and complexity. This work requires ESA permits and inspection and involves partial drywall opening in some areas.
Partial Updates
Some insurers will accept coverage if the K&T in the attic (the most accessible and most degraded area) is replaced or deactivated, with the remaining K&T circuits still in use but assessed as lower-risk. This is a negotiation with your specific insurer — not a code requirement. A licensed electrician can deactivate attic K&T and run new circuits for approximately $3,000–$8,000.
Buying a Home with Knob and Tube: What to Do
- Get a quote from a licensed ESA-registered electrician for full re-wire before waiving conditions
- Contact your insurance broker to confirm coverage is available and at what terms
- Negotiate a seller concession equal to the re-wire cost, or make seller-funded re-wire a condition of the sale
- Factor ongoing risk: if you proceed without immediate re-wire, you are living with a known hazard — ensure your smoke detectors are current and interconnected
ASADS inspectors document all visible knob and tube wiring with photos and provide a written assessment of condition and extent. Book your inspection at (647) 801-9311.
Buying an older Ontario home? Our pre-purchase inspection identifies knob-and-tube wiring, aluminum wiring, and other electrical hazards. Book today.