Home Indoor Air Quality in Ontario: What Home Inspectors Test and When to Be Concerned
ASADS Team · 2026-04-13
Why Indoor Air Quality Matters for Ontario Home Buyers
Canadians spend an average of 90% of their time indoors. The indoor environment of a home — its air quality, moisture levels, and contaminant load — has direct health implications that don't show up in a visual inspection alone.
Ontario homes face specific air quality risks that buyers should understand before purchasing, particularly in older housing stock where building materials and construction practices created conditions that accumulate over decades.
The Main Indoor Air Quality Concerns in Ontario Homes
1. Radon Gas
Radon is a naturally occurring radioactive gas that forms from the decay of uranium in soil and rock. It seeps into homes through foundation cracks, floor drains, and construction joints. Health Canada identifies radon as the second leading cause of lung cancer in Canada, responsible for approximately 3,200 deaths per year.
Ontario has areas of elevated radon concentration, particularly in the granite-rich Canadian Shield regions, but radon levels vary significantly even within the same neighbourhood. The only way to know if a home has elevated radon is to test.
Health Canada action level: 200 Bq/m³. Homes above this level should be mitigated. Long-term radon testing (90 days minimum) is the gold standard — short-term tests are directional only.
Testing cost: $25–$60 for a long-term charcoal test kit. Professional radon mitigation systems (sub-slab depressurization) cost $1,500–$3,000 if needed.
2. Mould and Biological Contaminants
Mould grows wherever moisture and organic material meet. In Ontario homes, the most common locations are:
- Basement walls and rim joists (chronic humidity, especially in homes without proper vapour barriers)
- Attic sheathing (bathroom fans venting into the attic space rather than outside — extremely common)
- Under kitchen and bathroom sinks (slow leaks that go unnoticed for months)
- Behind finished basement walls (water infiltration concealed by drywall)
- Around windows with poor seals or condensation issues
Visible mould is documented in the inspection report. Hidden mould — detectable via musty odours, moisture readings, or thermal imaging anomalies — warrants further investigation. Air quality testing for mould (spore counts, species identification) is a specialist service separate from a standard home inspection.
3. Carbon Monoxide
CO is produced by incomplete combustion from gas furnaces, water heaters, fireplaces, and attached garages. It's odourless and colourless — detector alarms are the only reliable warning system.
Key inspection findings related to CO risk:
- Cracked heat exchanger — allows combustion gases to mix with circulated air. A serious finding requiring immediate furnace replacement
- Back-drafting on furnaces and water heaters
- Missing or non-functional CO detectors (required within 15 feet of sleeping areas under Ontario's CO Detector Act)
- Blocked flue venting
4. Volatile Organic Compounds (VOCs)
VOCs are emitted as gases from certain solids and liquids — paints, varnishes, wax, cleaning products, building materials, and furnishings. In a home inspection context, the most significant sources are:
- Urea-formaldehyde foam insulation (UFFI) — injected into wall cavities in some 1970s–1980s Ontario homes as an energy retrofit. Banned in Canada in 1980 for residential use due to off-gassing. Still present in some older homes.
- New construction or recently renovated spaces with high off-gassing from materials
- Attached garages with vehicle exhaust migration
- Underground storage tanks (if fuel oil heat was converted) — petroleum VOC contamination
VOC testing requires air sampling sent to a lab — this is beyond the scope of a standard home inspection but can be arranged through environmental testing firms.
5. Asbestos Fibres
Asbestos-containing materials in good condition and undisturbed don't typically release fibres. The air quality risk arises when materials are deteriorated, damaged, or disturbed during renovation. Pre-1990 homes may contain asbestos in insulation, floor tiles, duct wrap, and ceiling textures. See our guide on vermiculite and asbestos insulation in Ontario homes.
What a Standard Home Inspection Covers (and What It Doesn't)
A home inspection is a visual assessment. Here's what's in scope for air quality:
Included in a Standard ASADS Inspection
- Visible mould documentation with photos
- Moisture readings in basement, bathroom, kitchen, and anywhere moisture staining is visible
- Thermal imaging to identify cold spots suggesting hidden moisture accumulation
- Furnace heat exchanger assessment (visual + carbon monoxide detector test near register)
- CO and smoke detector presence and function check
- Identification of suspected asbestos-containing materials (visual only — no sampling)
- HRV/ERV ventilation system assessment
- Attic ventilation balance check (connected to moisture and air quality)
Requires Specialist Testing (Beyond Standard Inspection)
- Radon testing: Long-term test kit or professional continuous monitor. Recommend for any home with a basement in Ontario.
- Mould air sampling: Spore counts and species identification require lab analysis. Relevant when hidden mould is suspected.
- Asbestos sampling: Bulk or air sampling by a designated substance surveyor (required under Ontario Regulation 278/05).
- VOC air testing: Environmental sampling firm. Relevant for UFFI homes, near underground tanks, or heavily renovated spaces.
- Water quality testing: Separate from air quality but important for well-water properties.
Thermal Imaging and Indoor Air Quality
Infrared thermal imaging is one of the most valuable tools for identifying air quality risk factors before they're visible. ASADS includes thermal imaging in every inspection at no extra charge. What it finds:
- Cold spots in walls and ceilings indicating moisture accumulation — often the first sign of hidden mould
- Basement wall temperature differentials showing water infiltration paths
- Gaps in building envelope where outside air (and soil gases including radon) infiltrate more easily
- Missing insulation creating condensation zones where biological growth can begin
Questions to Ask Before Buying a Pre-1990 Ontario Home
- Has radon testing ever been done? What were the results?
- Has there ever been moisture infiltration, flooding, or mould remediation in the basement?
- Was the home ever insulated with urea-formaldehyde foam (UFFI)?
- Is there vermiculite insulation in the attic?
- Were any underground fuel oil tanks removed — and do you have documentation of the removal and soil testing?
- What year was the furnace installed, and has the heat exchanger been inspected recently?
Book a Home Inspection in Ontario
ASADS Home Inspection serves the GTA and surrounding Ontario communities. Thermal imaging is included in every inspection. Our inspectors document air quality risk factors — visible mould, suspected ACM, CO safety concerns, ventilation deficiencies — in a same-day written report.
For specialist air quality testing (radon, mould sampling, VOCs), we can refer you to accredited Ontario labs and environmental consultants. Call (647) 801-9311 or book your inspection online.