Knob and Tube Wiring in Ontario Homes: Dangers & Insurance Impact
ASADS Home Inspection · 2026-04-13
What Is Knob and Tube Wiring?
Knob and tube (K&T) wiring was the standard electrical system in Canadian homes built roughly between 1880 and 1950. It gets its name from the two components that make it up: ceramic knobs that anchor the wire to joists and studs, and ceramic tubes that protect the wire where it passes through wood framing.
Unlike modern wiring, knob and tube runs two separate conductors — a hot wire and a neutral wire — spaced several inches apart through open air. There is no ground wire. The insulation is cloth or rubber, which degrades and becomes brittle over time.
In Ontario, knob and tube was phased out after the 1950s as grounded two-wire and eventually three-wire systems became code. However, it remains in tens of thousands of older homes across the province — particularly in Toronto, Hamilton, Kitchener, and other cities with significant pre-war housing stock.
Why Is Knob and Tube Wiring Dangerous?
Knob and tube wiring itself — when original and in good condition — is not inherently more dangerous than modern wiring. The problems arise from what happens to it over 70–100 years of service:
- Insulation deterioration: The original rubber and cloth insulation becomes brittle and cracks with age, heat cycling, and exposure to rodents. Cracked insulation on live wires is a direct fire and shock hazard.
- Improper modifications: The most dangerous knob and tube situations are almost always the result of amateur modifications — spliced connections in walls, unapproved junction boxes, extension cords wired directly to K&T runs, or modern wiring spliced incorrectly into old K&T circuits.
- Insulation contact: Knob and tube relies on air circulation for cooling. When blown-in or batt insulation is packed directly against K&T wire (very common in energy retrofits), the wire can overheat and ignite the surrounding insulation. This is one of the leading causes of K&T-related house fires.
- No ground: The absence of a ground conductor means no protection against electrical surges and a shock risk with modern three-prong appliances.
- Overloaded circuits: Original K&T circuits were designed for the electrical loads of 1930s homes — a few lights and outlets. Modern kitchens, home offices, and entertainment systems draw far more current than these circuits were designed to handle.
Knob and Tube Wiring and Home Insurance in Ontario
This is where knob and tube becomes a serious practical problem for Ontario homeowners and buyers. Most major insurers — including Intact, Aviva, Economical, and others — either refuse to insure homes with active knob and tube wiring or charge significantly higher premiums.
Some insurers will insure a K&T home only if:
- A licensed electrician certifies the wiring is in good condition and meets current standards
- The K&T has been fully replaced in high-risk areas (kitchen, bathroom, attic)
- The electrical panel has been upgraded from the original fuse box to a modern breaker panel
If you're buying a pre-1950 Ontario home, confirm with your insurance broker whether they'll cover it and on what terms before removing your inspection condition. Discovering an uninsurable home after closing is a costly surprise.
How to Identify Knob and Tube Wiring
Knob and tube wiring is most visible in unfinished basements and attics, where you can see the open framing. Look for:
- White or grey ceramic spools (knobs) nailed to joists with wire running through them
- White ceramic tubes where wire passes through framing
- Two separate wires running parallel, 4–6 inches apart, rather than a single sheathed cable
- Cloth or rubber insulation that appears dried, cracked, or flaking
- A fuse box (rather than a circuit breaker panel) — common in K&T-era homes
A certified home inspector will identify knob and tube wiring during a standard inspection and note its condition, any modifications, and any contact with insulation. This is one reason attending your home inspection is so valuable — your inspector can show you exactly what they found and where.
What Should You Do About Knob and Tube Wiring?
The right course of action depends on the condition of the wiring, the extent of coverage remaining, and your renovation plans:
- Full replacement: The safest and most insurance-friendly option. A licensed Ontario electrician replaces all K&T with modern grounded wiring. Cost typically runs $8,000–$20,000 depending on home size and how much of the K&T remains active.
- Partial replacement: High-risk circuits (kitchen, bathroom, attic) are replaced first. May be acceptable to some insurers as a phase-in approach.
- Electrical certification: An Electrical Safety Authority (ESA) inspection certifying the existing K&T meets current safety standards. Some insurers will accept this, but not all.
- Leave in place (if decommissioned): If the K&T has been properly disconnected and replaced — and is only visible as remnant hardware — it is not a concern.
Knob and Tube Wiring and Your Home Inspection
ASADS inspectors identify knob and tube wiring as part of every standard pre-purchase home inspection. We document the location, condition, any signs of modification or insulation contact, and the panel type. This gives buyers the information needed to negotiate repairs, request an ESA inspection, or make an informed decision before closing.
If you're buying an older Ontario home — particularly anything built before 1960 — assume K&T is present until proven otherwise. Our pre-purchase home inspection gives you a complete picture of the electrical system and every other major component before you commit.